Circuit Playground EXPRESS - Educators Pack

CIRCUITEXPRESS

u/moms: 1.000,00 DKK m/moms 1.250,00 DKK

Normal leveringstid 1 - 3 hverdage med tracking

Fri fragt (i Danmark) ved køb over 500 kr. (u. omdeling)

ELLER

PRODUKTBESKRIVELSE

Circuit Playground Express programmeres (ligesom micro:bit) med Makecode, altså blokprogrammering.

Det er en videreudviklng ad Circuit Playground Classic, som kodes med Arduino, og den kan endnu mere. Særligt, hvis du har lyst til at arbejde med e-tekstil og wearables. 

Den kan også kodes med CircuitPython. Du KAN også programmere med det mere avancerede Arduino IDE.

Boardet er rundt og har "ben" til krokodillenæb eller til ledende tråd. Ingen brug for lodning.

Du kan give strøm via USB eller batteriholderen med AAA - eller måske med et Lipoly batteri.

Denne "madkasse" med educators pack rummer rigeligt med materialer til en eller to brugere.

Indhold:

    2 x Circuit Playground Express fra Adafruit
    2 x USB cable - A/MicroB

    1 x Stainless Thin Conductive Thread - 2 ply - 23 meter/76 ft for sewing wearable projects
    1 x Needle set - 3/9 sizes - 20 needles
    1 x Sewable Snaps - 5mm Diameter - Card of 24
    1 x Magnetic Pin Back

    1 x Copper Foil Tape with Conductive Adhesive - 6mm x 15 meter roll
    1 x Small Alligator Clip Test Lead (set of 18)
    1 x Small Alligator Clip to Male Jumper Wire Bundle - 6 Pieces

Extra RGB and multicolor LEDs, and two motors:

    2 x Micro Servo - til at  ave små robotter
    1 x Flora RGB Smart NeoPixel version 2 - Pack of 4
    1 x Adafruit LED Sequins - Multicolor Pack of 5

Forskellige batteriholdere:

    1 x JST-PH Battery Extension Cable - 500mm - Extension cables for the battery holders
    1 x 3x AAA Battery Holder with On/Off Switch, JST, and Belt Clip
    3 x Alkaline AAA batteries
    1 x 3x AA Battery Holder with On/Off Switch, JST, and Belt Clip
    3 x Alkaline AA batteries

    2 x Mini Storage Box
    1 x AdaBot LunchBox!

Hvad er der på Curcuit Playground Express:

    10 x mini NeoPixels, each one can display any color
    1 x Motion sensor (LIS3DH triple-axis accelerometer with tap detection, free-fall detection)
    1 x Temperature sensor (thermistor)
    1 x Light sensor (phototransistor). Can also act as a color sensor and pulse sensor.
    1 x Sound sensor (MEMS microphone)
    1 x Mini speaker with class D amplifier (7.5mm magnetic speaker/buzzer)
    2 x Push buttons, labeled A and B
    1 x Slide switch
    Infrared receiver and transmitter - can receive and transmit any remote control codes, as well as send messages between Circuit Playground Expresses. Can also act as a proximity sensor.
    8 x alligator-clip friendly input/output pins
    Includes I2C, UART, 8 pins that can do analog inputs, multiple PWM output
    7 pads can act as capacitive touch inputs and the 1 remaining is a true analog output
    Green "ON" LED so you know its powered
    Red "#13" LED for basic blinking
    Reset button
    ATSAMD21 ARM Cortex M0 Processor, running at 3.3V and 48MHz
    2 MB of SPI Flash storage, used primarily with CircuitPython to store code and libraries.
    MicroUSB port for programming and debugging
    USB port can act like serial port, keyboard, mouse, joystick or MIDI!


Her er også en vejledning til et sjovt spil med Laser-pen.


https://learn.adafruit.com/circuit-playground-express-laser-tag/build-a-cpx-laser-tag-game

Detaljer

Circuit Playground Express programmeres (ligesom micro:bit) med Makecode, altså blokprogrammering.

Det er en videreudviklng ad Circuit Playground Classic, som kodes med Arduino, og den kan endnu mere. Særligt, hvis du har lyst til at arbejde med e-tekstil og wearables. 

Den kan også kodes med CircuitPython. Du KAN også programmere med det mere avancerede Arduino IDE.

Boardet er rundt og har "ben" til krokodillenæb eller til ledende tråd. Ingen brug for lodning.

Du kan give strøm via USB eller batteriholderen med AAA - eller måske med et Lipoly batteri.

Denne "madkasse" med educators pack rummer rigeligt med materialer til en eller to brugere.

Indhold:

    2 x Circuit Playground Express fra Adafruit
    2 x USB cable - A/MicroB

    1 x Stainless Thin Conductive Thread - 2 ply - 23 meter/76 ft for sewing wearable projects
    1 x Needle set - 3/9 sizes - 20 needles
    1 x Sewable Snaps - 5mm Diameter - Card of 24
    1 x Magnetic Pin Back

    1 x Copper Foil Tape with Conductive Adhesive - 6mm x 15 meter roll
    1 x Small Alligator Clip Test Lead (set of 18)
    1 x Small Alligator Clip to Male Jumper Wire Bundle - 6 Pieces

Extra RGB and multicolor LEDs, and two motors:

    2 x Micro Servo - til at  ave små robotter
    1 x Flora RGB Smart NeoPixel version 2 - Pack of 4
    1 x Adafruit LED Sequins - Multicolor Pack of 5

Forskellige batteriholdere:

    1 x JST-PH Battery Extension Cable - 500mm - Extension cables for the battery holders
    1 x 3x AAA Battery Holder with On/Off Switch, JST, and Belt Clip
    3 x Alkaline AAA batteries
    1 x 3x AA Battery Holder with On/Off Switch, JST, and Belt Clip
    3 x Alkaline AA batteries

    2 x Mini Storage Box
    1 x AdaBot LunchBox!

Hvad er der på Curcuit Playground Express:

    10 x mini NeoPixels, each one can display any color
    1 x Motion sensor (LIS3DH triple-axis accelerometer with tap detection, free-fall detection)
    1 x Temperature sensor (thermistor)
    1 x Light sensor (phototransistor). Can also act as a color sensor and pulse sensor.
    1 x Sound sensor (MEMS microphone)
    1 x Mini speaker with class D amplifier (7.5mm magnetic speaker/buzzer)
    2 x Push buttons, labeled A and B
    1 x Slide switch
    Infrared receiver and transmitter - can receive and transmit any remote control codes, as well as send messages between Circuit Playground Expresses. Can also act as a proximity sensor.
    8 x alligator-clip friendly input/output pins
    Includes I2C, UART, 8 pins that can do analog inputs, multiple PWM output
    7 pads can act as capacitive touch inputs and the 1 remaining is a true analog output
    Green "ON" LED so you know its powered
    Red "#13" LED for basic blinking
    Reset button
    ATSAMD21 ARM Cortex M0 Processor, running at 3.3V and 48MHz
    2 MB of SPI Flash storage, used primarily with CircuitPython to store code and libraries.
    MicroUSB port for programming and debugging
    USB port can act like serial port, keyboard, mouse, joystick or MIDI!


Her er også en vejledning til et sjovt spil med Laser-pen.


https://learn.adafruit.com/circuit-playground-express-laser-tag/build-a-cpx-laser-tag-game

Vi anbefaler

Vi anbefaler